 |
| Quantity: | |
|---|---|
UM4000-SR55-AU
Piezohannas
UM4000-SR55-AU
Long Range Ultrasonic Module Distance Measuring Transducer Sensor
Applications:
Surface -mount ,Range of up to 4m enables reliable long-range detection.
Suitable for distance,liquid level,level measurement ,perception,anti-collision field high protection level can be used outdoors.
AC power supply available
Different output version offer: digital,analog,ready contact or switching output
IP68 Enclosure Rating
Parameters：
Ultrasonic sensor | Technical data |
General Specifications | |
Sensing distance | 280…4000mm(200---3000mm) |
Adjustment range | 280…4000mm |
Unusable area | 0…280mm |
Standard target plate | 100mm×100mm |
Transducer frequency About | 75 kHz |
Response delay About | 125ms |
Indicators/Operating means | |
LED yellow | solid: NO LED |
LED red | flashing: |
Electrical specifications | |
Operating voltage UB | 10…30VDC ripple10%ss |
No-load supply current | ≤30mA |
Output | |
Output type | 1 analogue output 0---5V |
Resolution | |
Deviation of the characteristic | ±1% of full-scale value |
Repeat accuracy | ±0.1% of full-scale value |
Load impedance | >1k Ohm |
Maximum switching current | mA |
Temperature influence | ±1.5% of full-scale value |
Ambient conditions | |
Ambient temperature | -25…70℃ |
Storage temperature | -40…85℃ |
Mechanical specifications | |
Protection grade | IP68 |
Connection | PVC cable,4-PIN |
Material | |
Housing | PBT OR FRP |
Transducer | epoxy resin/hollow glass sphere |
Weight | 150g |
Compliance with standards and Directives | |
Standard conformity | EN 60947-5-2:2007 |
Dimension:
Adjusting the evaluation limits
The ultrasonic sensor features an analogue output with two teachable evaluation limits. These are set by applying the supply
voltage -UB or +UB to the TEACH-IN input. The supply voltage must be applied to the TEACH-IN input for at least 1 s.
indicate whether the sensor has recognised the target during the TEACH-IN procedure. The lower evaluation limit A1 is taught
with -UB, A2 with +UB.
Two different output functions can be set:
1. Analogue value increases with rising distance to object (rising ramp)
2. Analogue value falls with rising distance to object (falling ramp)
Evaluation limits may only be specified within the first 5 minutes after
Power on. To modify the evaluation limits later,
the user may specify the desired values only after a new Power On.
TEACH-IN rising ramp (A2 > A1)
- Position object at lower evaluation limit
- TEACH-IN lower limit A1 with - UB
- Position object at upper evaluation limit
- TEACH-IN upper limit A2 with + UB
TEACH-IN falling ramp (A1 > A2):
- Position object at lower evaluation limit
- TEACH-IN lower limit A2 with + UB
- Position object at upper evaluation limit
- TEACH-IN upper limit A1 with - UB
Default setting
A1: unusable area
A2: nominal sensing range
Mode of operation: rising ramp
LED Displays (SMP80 series no led)
Displays in dependence on operating mode | Red LED | Yellow LED |
TEACH-IN evaluation limit Object detected No object detected Object uncertain (TEACH-IN invalid) |
off flases on |
flashes off off |
Normal mode (evaluation range) | off | on |
Fault | on | previous state |
Notice:
1. Basically, there are two versions of ordinary blind zone and small blind zone for each type, and you can contact us if you need different ranges and blind zones;
2. Each type basically has analog output: 0-5V, 0-10V, 0-20mA, 4--20mA ;
Digital output: RS232/485, UART TTL and I2C and other output modes ,they are optional;
3. Most types has high voltage series (10---30V) and low voltage series (3.6---5V).
Long Range Ultrasonic Module Distance Measuring Transducer Sensor
Applications:
Surface -mount ,Range of up to 4m enables reliable long-range detection.
Suitable for distance,liquid level,level measurement ,perception,anti-collision field high protection level can be used outdoors.
AC power supply available
Different output version offer: digital,analog,ready contact or switching output
IP68 Enclosure Rating
Parameters：
Ultrasonic sensor | Technical data |
General Specifications | |
Sensing distance | 280…4000mm(200---3000mm) |
Adjustment range | 280…4000mm |
Unusable area | 0…280mm |
Standard target plate | 100mm×100mm |
Transducer frequency About | 75 kHz |
Response delay About | 125ms |
Indicators/Operating means | |
LED yellow | solid: NO LED |
LED red | flashing: |
Electrical specifications | |
Operating voltage UB | 10…30VDC ripple10%ss |
No-load supply current | ≤30mA |
Output | |
Output type | 1 analogue output 0---5V |
Resolution | |
Deviation of the characteristic | ±1% of full-scale value |
Repeat accuracy | ±0.1% of full-scale value |
Load impedance | >1k Ohm |
Maximum switching current | mA |
Temperature influence | ±1.5% of full-scale value |
Ambient conditions | |
Ambient temperature | -25…70℃ |
Storage temperature | -40…85℃ |
Mechanical specifications | |
Protection grade | IP68 |
Connection | PVC cable,4-PIN |
Material | |
Housing | PBT OR FRP |
Transducer | epoxy resin/hollow glass sphere |
Weight | 150g |
Compliance with standards and Directives | |
Standard conformity | EN 60947-5-2:2007 |
Dimension:
Adjusting the evaluation limits
The ultrasonic sensor features an analogue output with two teachable evaluation limits. These are set by applying the supply
voltage -UB or +UB to the TEACH-IN input. The supply voltage must be applied to the TEACH-IN input for at least 1 s.
indicate whether the sensor has recognised the target during the TEACH-IN procedure. The lower evaluation limit A1 is taught
with -UB, A2 with +UB.
Two different output functions can be set:
1. Analogue value increases with rising distance to object (rising ramp)
2. Analogue value falls with rising distance to object (falling ramp)
Evaluation limits may only be specified within the first 5 minutes after
Power on. To modify the evaluation limits later,
the user may specify the desired values only after a new Power On.
TEACH-IN rising ramp (A2 > A1)
- Position object at lower evaluation limit
- TEACH-IN lower limit A1 with - UB
- Position object at upper evaluation limit
- TEACH-IN upper limit A2 with + UB
TEACH-IN falling ramp (A1 > A2):
- Position object at lower evaluation limit
- TEACH-IN lower limit A2 with + UB
- Position object at upper evaluation limit
- TEACH-IN upper limit A1 with - UB
Default setting
A1: unusable area
A2: nominal sensing range
Mode of operation: rising ramp
LED Displays (SMP80 series no led)
Displays in dependence on operating mode | Red LED | Yellow LED |
TEACH-IN evaluation limit Object detected No object detected Object uncertain (TEACH-IN invalid) |
off flases on |
flashes off off |
Normal mode (evaluation range) | off | on |
Fault | on | previous state |
Notice:
1. Basically, there are two versions of ordinary blind zone and small blind zone for each type, and you can contact us if you need different ranges and blind zones;
2. Each type basically has analog output: 0-5V, 0-10V, 0-20mA, 4--20mA ;
Digital output: RS232/485, UART TTL and I2C and other output modes ,they are optional;
3. Most types has high voltage series (10---30V) and low voltage series (3.6---5V).
