Making of Arduino piano pickup with piezoelectric sensor

Step 1: Components

pzt material piezo ceramics piezoelectric transducer

speaker

Breadboard

Arduino Uno

Jumper

6 resistors

Step 2: Connect

The red wire of each piezoelectric sensor should be connected to GND through a resistor, and the black wire should be connected to Pin. Here we use A0, A1, A2, A3, A4, A5

The red wire of the speaker should be connected to pin 8 and the black wire should be connected to GND

Step 3:

First of all

You need to open "New Tab" and name the file "pitches.h", then insert the pitch of piezo ceramic crystal

#define NOTE_CS2 69

#define NOTE_D2 73

#define NOTE_DS2 78

#define NOTE_E2 82

#define NOTE_F2 87

#define NOTE_FS2 93

#define NOTE_G2 98

#define NOTE_GS2 104

#define NOTE_A2 110

#define NOTE_AS2 117

#define NOTE_B2 123

#define NOTE_C3 131

#define NOTE_CS3 139

＃NOTE_D3 147

#define NOTE_DS3 156

#define NOTE_E3 165

#define NOTE_F3 175

#define NOTE_FS3 185

#define NOTE_G3 196

#define NOTE_GS3 208

#define NOTE_A3 220

#define NOTE_AS3 233

#define NOTE_B 3247

#define NOTE_C4 262

#define NOTE_CS4 277

#define NOTE_D4 294

#define NOTE_DS4 311

#define NOTE_E4 330

#define NOTE_F4 349

#define NOTE_FS4 370

#define NOTE_G4 392

#define NOTE_GS4 415

#define NOTE_A4 440

#define NOTE_AS4 466

#define NOTE_B4 494

#define NOTE_C5 523

#define NOTE_CS5 554

#define NOTE_D5 587

#define NOTE_DS5 622

#define NOTE_E5 659

#define NOTE_F5 698

#define NOTE_FS5 740

#define NOTE_G5 784

#define NOTE_GS5 831

#define NOTE_A5 880

#define NOTE_AS5 932

#define NOTE_B5 988

#define NOTE_C6 1047

#define NOTE_CS6 1109

#define NOTE_D6 1175

#define NOTE_DS6 1245

#define NOTE_E6 1319

#define NOTE_F6 1397

#define NOTE_FS6 1480

#define NOTE_G6 1568

#define NOTE_GS6 1661

#define NOTE_A6 1760

#define NOTE_AS6 1865

#define NOTE_B6 1976

#define NOTE_C7 2093

#define NOTE_CS7 2217

#define NOTE_D7 2349

#define NOTE_DS7 2489

#define NOTE_E7 2637

#define NOTE_F7 2794

#define NOTE_FS7 2960

#define NOTE_G7 3136

#define NOTE_GS7 3322

#define NOTE_A7 3520

#define NOTE_AS7 3729

#define NOTE_B7 3951

#define NOTE_C8 4186

#define NOTE_CS8 4435

#define NOTE_D8 4699

#define NOTE_DS8 4978

After that, go back to the sketch and add your sketch code

#include“ pitches.h”

Int Analog pin = {A0，A1，A2，A3，A4，A5};

int buzpin = 8;

int= 20;

Invalid setup（）

Serial.begin（9600）;

pinMode（8，OUTPUT）;

}

void loop（）

if（analogRead （analogpin ［0］）》 threshold）

Serial.println（“ A0”）;

tone（8，NOTE _B4，1000/4）;

If（analogRead（analogpin ）》

Serial.println（“ A1”） ;

tone（8，NOTE_D4，1000/4）;

digitalWrite（8，HIGH）;

if（ AnalogRead（analogpin ［2］）》）

Serial.println（“ A2”）;

tone（8，NOTE_C4，1000/4 ）;

If（analogRead（analogpin ［3］）》）

Serial.println（“ A3 “）;

tone（8，NOTE_G4，1000/4）;

if（analogRead（analogpin ［4］）》）

Serial.println（“ A4”）;

tone（8，NOTE_G3，1000/4）;

if（analogRead（analogpin ［5］）》）

Serial.println（“ A5”）;

tone（8，NOTE_D3，1000/4）;

Step 4: Conclusion

In Wikipedia, piezoelectric discs piezoelectric transducers are devices that use the piezoelectric effect to measure changes in pressure, acceleration, temperature, strain or force and convert them into electrical charges. The prefix piezo- is the Greek word for ‘press’ or ‘squeeze’.

So we use it to detect when each pad is pressed, so the Arduino will decide which tone to play, and the idea that you can play in it can develop into a complete one.